Olympus UK E-System User Group
Olympus UK E-System User Group

Join our unique resource for Olympus Four Thirds E-System DSLR and Pen and OM-D Micro Four Thirds photographers. Show your images via our free e-group photo gallery. Please read the e-group.uk.net forum terms and conditions before posting for the first time. Above all, welcome!


Go Back   Olympus UK E-System User Group > Cameras, lenses and system accessories > Camera conference > Olympus E-5

Olympus E-5 E-5 specific discussion.

Reply
 
Thread Tools Display Modes
  #1  
Old 11th June 2017
Ivor
Guest
 
Posts: n/a
screw size

Hi all,

Does anyone know or can tell me the specifications of the two little flat-headed countersunk screws that hold the tripod mount in place on the base of an E-5, please? Mine are missing.

Searching the internet I can see that them coming loose is an issue with E-3s and E-5s, so when I source new ones a drop of glue is going on the thread. Anyone else with an E-3 or E-5, it might be worth checking yours. I can't find any reference to the screw specifications though.

I have a whole load of tiny screws from various electronics and computer building projects, but not one is the right size.

Cheers,

Ivor
Reply With Quote
  #2  
Old 11th June 2017
Shaw's Avatar
Shaw Shaw is offline
Senior
 
Join Date: Nov 2007
Location: Howe o' the Mearns, Aberdeenshire
Posts: 1,151
Thanks: 204
Thanked 173 Times in 101 Posts
Likes: 466
Liked 162 Times in 62 Posts
Re: screw size

Luton Cameras should be able to get them for you.
__________________
Stewart

My Zenfolio Site
My Portfolio Site

Olympus: E-M1 Mk11 | PEN-F + ECG-4 | XZ-1 | EE-1 Dot Sight Lumix: G9 | LX100 Nissin: i40
Zuiko: 40-150 Pro + MC-14 | 12-100 Pro | 7-14 Pro | 17 | 45 | 60 | OM 135 Leica: 100-400 | 12-60 Samyang: 7.5 fisheye Tamron: 14-150
Reply With Quote
The Following User Says Thank You to Shaw For This Useful Post:
The Following User Liked This Post:
Graham_of_Rainham (11th June 2017)
  #3  
Old 11th June 2017
Ivor
Guest
 
Posts: n/a
Re: screw size

Yes, thanks.

I was thinking of giving them a ring tomorrow as I also need a replacement rubber for the base of the camera too. The rubber is 6.50 for 1/2 a square inch and a bit of sticky tape, and that seems excessive to me.

Based on that, I suspect the screws, that probably cost 1.50 to buy a packet of 100 elsewhere will probably be 10 a pair from there. That was why I was wondering if anyone knew the dimensions.

Cheers,
Reply With Quote
The Following User Liked This Post:
Shaw (11th June 2017)
  #4  
Old 11th June 2017
Graham_of_Rainham's Avatar
Graham_of_Rainham Graham_of_Rainham is offline
Administrator
 
Join Date: Nov 2007
Location: Rainham
Posts: 8,223
Thanks: 647
Thanked 951 Times in 735 Posts
Likes: 2,313
Liked 1,624 Times in 937 Posts
Re: screw size

The only reference I can find for the screws is:

Item 277 Pt No.WE127012 Description PSTB24.5SN

You may find that an "alternative" approach may provide a solution:

http://www.ebay.co.uk/itm/For-Apple-...wAAOSwFV9X0rnR

Good luck
__________________
Graham

We often repeat the mistakes we most enjoy...
Reply With Quote
The Following User Says Thank You to Graham_of_Rainham For This Useful Post:
  #5  
Old 11th June 2017
Ivor
Guest
 
Posts: n/a
Re: screw size

Thanks Graham. I have just been hunting through ebay and found lots of watch screws, with rounded heads, but hadn't seen those. I'll give them a try.

Cheers,

Ivor
Reply With Quote
  #6  
Old 11th June 2017
peak4's Avatar
peak4 peak4 is offline
Full member
 
Join Date: Nov 2007
Location: Buxton, Derbyshire.
Posts: 1,727
Thanks: 131
Thanked 223 Times in 188 Posts
Likes: 220
Liked 195 Times in 130 Posts
Re: screw size

I've just measured one out of my E-3, and I can't easily spot a replacement on line in the UK,
M2 x 5mm wafer head, but with the smaller diameter head, rather than the normal 4mm ones.
2nd item on this page from the USA

M2x5mm OEM Wafer Head
LaptopMachine Screw
Average Overall Length: 5.45mm
Average Head Width: 2.81mm
Average Head Thickness: 0.63
Thread Pitch: 0.40
Drive: Phillips
Item #10139

The ones on my E-5 are slightly shorter at 4.5mm overall and silver, rather then black, so maybe it depends on which batch of screws they used.

N.B. I've not been able to check the thread pitch as I've no metric thread gauges and my 2mm taps and die seem to be missing out of the box.
I think they're probably over in Sheffield from when I was making some 2mm screws to repair a spotting scope.
__________________
Best Regards
Bill

The nearest I have to a home page.
http://www.flickr.com/photos/peak4/
They're Watching You!
Reply With Quote
Reply

Tags
e-5, screw size, tripod mount

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
A screw loose. Beagletorque The lounge 4 23rd May 2016 04:59 PM
HELP! Screw-on hood for Olympus 14-42mm II R Loup Garou Standard zoom and mid range 2 9th March 2016 01:52 PM
HELP! Lost Manfrotto screw bilbo Accessory talk 11 3rd December 2013 07:41 PM
screw on teleconverters mikey78 Lens focus 1 7th May 2011 08:52 AM
Screw in WA/Fisheye adaptors Ken Lister Converters, adapters and extension tubes 12 20th August 2010 04:20 PM


All times are GMT. The time now is 12:01 AM.


The Write Technology Ltd, 2007-2019, All rights reservedAd Management plugin by RedTyger